Every guide is free — start with the Start Here guide →
Plain-Language Knitting GuidesKnitBeginnersStart Learning

How to Join Yarn in Knitting: Invisible, Secure Joins Without Knots

By the KnitBeginners team · Published 5 November 2026 · Updated 19 November 2026

How to join yarn in knitting, in one sentence: connect the new ball to the old yarn in a way that holds under wear and washing, does not show on the finished fabric, and does not rely on a knot. Every project longer than one ball needs a join, and the method you choose depends on your yarn: animal fibers felt together, smooth fibers need a woven join, and a simple overlap works when the join can hide in a seam. This page covers the three reliable methods, which yarn each suits, and the one rule that matters most — never join with a knot in the middle of a row.

WHICH JOIN FOR WHICH YARNYarn and placeRecommended joinWool (felting), anywhereSpit splice.Wool, cotton, acrylic,Russian join.blends — mid-rowAny yarn, bulky — edge orOverlap join.seamSuperwash wool, cotton,Russian join or overlap join.acrylicAny yarn, first project —Overlap join (simplest).edge
Infographic: which yarn join to use — spit splice, Russian join, or overlap join, by yarn and place.

The Golden Rule: Join at the Edge When You Can

Two yarn ends being spliced together with a tapestry needle, no knot visible.

Whenever possible, join new yarn at the edge of the work — at the start of a row — rather than in the middle. An edge join hides in the seam or the border, and the loose ends are easy to weave in. If a ball runs out mid-row, you have two choices: work to the end of the row with the old ball if a few inches remain, or join mid-row with one of the methods below. Mid-row joins are fine when done well; they just need more care to stay invisible.

Method 1: The Russian Join (Best All-Rounder)

The Russian join works with most yarns, including smooth plant and synthetic fibers that will not felt. It weaves each yarn end back into itself, creating a doubled section that is secure without a knot and barely visible in the fabric.

Steps:

  1. Thread the old yarn tail onto a yarn needle.
  2. Weave the needle back through the old yarn itself for about 2 inches, following the ply twist, then pull the tail through so the yarn loops back on itself.
  3. Thread the new yarn tail onto the needle and weave it back through the new yarn the same way, so the two loops interlock.
  4. Pull both yarns gently to close the loops, trim any tiny tails, and keep knitting. The doubled section is slightly thicker for a few stitches, which disappears into the fabric after a row or two.

Best for: most yarns, especially smooth or slippery fibers, and mid-row joins where invisibility matters. Less good for: very bulky yarn, where the doubled section can show as a thick spot — use the overlap join instead.

Method 2: The Spit Splice (Animal Fibers Only)

The spit splice, also called the felted join, works only with animal fibers — wool and similar yarns whose fibers felt together when wet and rubbed. It makes a join with no added bulk and no ends to weave in, which is why it is the favorite method for wool garments.

Steps:

  1. Untwist a few inches of each yarn end so the fibers fan out.
  2. Overlap the fanned ends, wet them slightly, and rub them briskly between your palms. The friction and moisture felt the fibers together into a single strand.
  3. Check the join by pulling gently. If it holds, keep knitting. If it slips, re-wet and rub longer.

Best for: 100% wool and other felting animal fibers. Do not use for: cotton, acrylic, superwash wool (treated not to felt), or any yarn blend where felting is unreliable. A spit splice on a non-felting yarn will come apart in the finished piece.

Method 3: The Simple Overlap Join

The overlap join is the simplest method: hold the old and new yarn together and knit a few stitches with both strands held as one, then drop the old tail and continue with the new yarn alone. Weave both tails into the fabric afterward.

Steps:

  1. When a few inches of old yarn remain, lay the new yarn alongside it so they overlap for about 4 inches.
  2. Knit 3 to 4 stitches holding both strands together as if they were one yarn.
  3. Drop the old tail and continue with the new yarn alone.
  4. Weave both tails into the fabric on the wrong side, following the stitch path so they disappear.

Best for: bulky yarn, beginners, and edge joins where the tails can hide in a seam. Less good for: fine yarn in the middle of a visible row, where the doubled stitches can show as a thick spot.

Which Join Method Should You Use?

Yarn type Join location Recommended method
Wool (felting) Anywhere Spit splice
Wool, cotton, acrylic, blends Mid-row, must be invisible Russian join
Any yarn, bulky weight Edge or seam Overlap join
Superwash wool, cotton, acrylic Anywhere Russian join or overlap join
Any yarn, first project Edge of work Overlap join (simplest)

What Not to Do

Frequently Asked Questions

How do you join yarn in knitting without a knot?

Use the Russian join (weave each tail back into its own yarn so the loops interlock), the spit splice for felting wool (wet and rub the fanned ends together), or the overlap join (knit a few stitches with both yarns held together, then weave in the tails).

How do you add yarn when knitting?

Join the new ball at the edge of the work if possible, or mid-row with a Russian join or overlap join. Leave generous tails, test the join by pulling firmly, and weave the tails into the wrong side of the fabric.

What is the best way to join wool yarn?

The spit splice, for 100% wool that felts: fanning, wetting, and rubbing the ends together makes a join with no bulk and no ends to weave in. For superwash wool, which does not felt, use the Russian join instead.

Can you join yarn in the middle of a row?

Yes. The Russian join is the best mid-row method for most yarns because it is invisible and secure. Joining at the edge is preferable when you can plan it, but a good mid-row join will not show.

How do you attach new yarn when knitting a scarf?

Join at the edge of a row if you can, using the overlap join for simplicity or the Russian join for invisibility. Weave the tails into the edge stitches so they disappear into the border.

Next step: continue with Knitting for Beginners — Start Here →